二、结构特征
本机由YD系列三相异步通过三角皮带和一级园柱齿轮，带动主轴旋转，主轴上装有三种凸轮机构的作用，边疆完成填充、压制、出片三个工艺程序；每个程序均可调节，以满足技术参数的要求。
三、安装及调试
1、整机安装：
整机可用钢丝绳串入顶部吊运，也可用铲车搬运，机器就位前应整机校平。
2、电源线的安装：
电缆规格与电机功率，电压和电流相适应。电缆通过总开关经电线管或插座插头用软电缆连接；电缆通过机座后的出线圈进入电气箱。
电动机的转向应与指示标牌*（即从电动机上带轮外端看为逆时针方向旋转），校对转向前应将三角皮带拆下，校对后装上三角皮带，再通过顺点运按钮确认转向的正确性。
3、首先切断机器上的电源，拆下料斗44，加料器57和中模台板19，将中模台板的模孔，上下冲杆孔和冲模揩擦干净，然后按照以下步骤进行。
（1）首先将下冲钉插入下冲杆21的孔内，插足至根部，然后对准机身的缺口拧紧螺钉59；
（2）将上冲钉装入上冲杆16孔内，插足至根部，拧紧紧固螺钉
（3）将中模装入中模台板19孔内，注意中模的端面须低于台板平面0~0.05mm，紧固两边的紧定螺钉42。
（4）将中模台板装上机身，套入下冲，转动大皮带轮32，使上冲进入中模孔内，应间隙均匀，上下灵活，无干涉和硬摩擦现象，再固紧中模台板与机身的固定螺栓
（5）装上加料器等被拆下的零件。
4、充填深度的调整
拧松充填调节螺母两侧的紧定螺钉，螺母放置下降即可增加充填深度，调整后必须拧紧紧固螺钉，注意充填深度不得超过45mm。
5、片剂厚度的调整
与上冲杆相连接的偏心壳体05上的偏心套35，装有标尺，其数值表示上冲进入中模的深度。调整进先拧松偏心壳体05上面的紧固螺栓，通过锥形齿轮带动偏心套35即可调整片厚，调整后须把螺栓螺母拧紧，防止松动。
6、出片调整
转动带轮（顺转），使下冲升到zui高位置，拧松出片调节螺母两侧螺钉，旋转出片调节螺母，使下冲上端面与中模端面平齐，调整后，固紧两侧螺钉。
7、加料器调整
转动带轮使下冲上端面上升到zui高（与中模相平）时，调节活络接头（调前应先松螺母），使加料器前端面靠近下冲外径边缘坚固螺母，再转动带轮（必须顺转）使加料器进退运动几次仍符合要求即可。
8、下冲杠杆的位置调整直接影响填充量的稳定性。转动带轮使下冲下降zui低位置，即是充填调节螺母靠紧机身，调节上下螺母，使下冲杠杆的半园头贴紧充填调节螺母上端面，并紧上下螺母即可。
四、使用与操作
1、机器使用前须检查冲模是否有缺边、裂缝、变形等质量问题，检查机器各装置是否完好。
2、检查颗粒原粒是否符合要求，颗粒中的细粉含量不宜超过10%，以免影响机器使用性能及寿命。
3、开车前应用手转动带轮或顺点动按钮试压，确定片剂符合要求，机器运转正常后，方可开机投入生产。
4、机器设有倒车点动按钮，压片时产生叠片或上冲粘冲闷车及校核上冲进模情况进可使用，使用时只允许瞬时点动使机器微量反转，否则会损坏机件。
5、使用中要随时注意机器的运转情况，如有异常声响，即应停机检查，排除故障后再使用。
五、维护与保护
1、机件上装有油杯，可按油杯的类型，分别注以润滑油或润滑脂。开机前应全部加油一次，生产中可视轴承温升和运转情况添加。
2、定期检查机件是否运转灵活和磨损情况，发现缺陷，应及时修复。
3、一次使用完毕或停产时，应刷清机器各部分的残留粉子；如停用时间较长，须将冲模拆下，并将机器全部擦拭干净，机件光面涂上防锈油。
4、冲模的保养：擦洗清洁，干燥涂上防锈油脂后，放置在合适的容器内，保持洁净，防止磕碰损伤。
六、注意事项
1、接电源时应注意机器的运转方向，切勿倒转；台免损坏机件。
2、机器调试时，应切断电源，避免引起伤害事故。
3、倒点运按钮只能在卸压或调试观察上冲进模情况时使用，不能随意使用，以免损坏机件造成事故。
4、机器上的防护罩，安全盖等使用前应装妥，不能拆除。
5、冲模应无裂纹、变形、缺边等质量问题，不合格品切勿使用，以免机器损坏和影响片剂质量。
6、调节机件或排除故障，必须停机进行，以免引起人身伤害。
7、加油时，勿使油溢到外面，以免污染物料影响片剂质量。 Basket type tablet machine details: Basket type tablet press is a small, basket type continuous automatic tablet machine. It is a medicine chemical industry, food, electronics and other industries processing for pressing granular raw materials into tablets or granules one of necessary equipments. It is suitable for small batch production, laboratory, hospital and other departments to suppress tablets, sugar tablets, touch of coal, calcium, coffee tablet, powder metallurgy, electronic components and a variety of agricultural fertilizer tablet. It can suppress various special-shaped, ringlike tablets, and can suppress the engraved with the trademark double-sided, text and simple graphics tablet. Basket type tablet machine technical parameters: The maximum compression pressure: 40/100/100kn Maximum diameter of tablet: 30/40/50mm Max filling depth: 25/45/45mm Annular plate diameter: 22/35/35mm Annular plate aperture: 5-10/6-14/6-14mm Annular slice filling depth: 25/45/45mm Production capacity: 2070/2100/2760 /h Motor power: 4/3.7/5.5 kw Dimensions: 685 x 565 x 1610mm 666 x 860 x 1824mm 666 x 860 x 1824mm Machine weight: 520/620/770kg Basket type tablet machine details: One, main application and applicable scope This machine belongs to a medium-sized basket type tablet machine, applicable to the pharmaceutical, chemical, food, electronic, fuel and other industries to the granular material is pressed into tablet form or flakes. This function is to suppress all kinds of circular, annular, special-shaped tablets, can suppress the engraved with the trademark double-sided, text and simple graphics tablet. This machine is suitable for semi solid, wet powder and powder pressing. Two, structural characteristics This machine is composed of YD series three-phase asynchronous through a triangle belt and a cylindrical gear, drives the rotation of the spindle, the spindle is provided with a three cam mechanism, the completion of filling, compaction, a three process; each procedure can be adjusted, in order to meet the technical parameters of the request. In three, the installation and debugging 1, the complete machine installation: The machine used wire rope strung into the top lifting, can also be used forklift handling, place should the leveling machine. 2, power line installation: Specification of cable and motor power, voltage and current to adapt. Cable through the master switch or socket plug through a wire tube with a soft cable; cable through the base after the wire coils into the electric box. The turning of the motor should be consistent with signs （ i.e. from the motor belt wheel outer end to counterclockwise）, proofreading before turning belt should be removed, proofreading mounted after the triangle belt, then transported along button to confirm the direction. In 3, the first cut off the power supply on the machine, remove the hopper feeder 44, 57 and 19 mold platen, will die platen die holes, on the lower punch hole and die wipe clean, then according to the following steps. （ 1） the undershoot undershoot rod pin is inserted into the 21 hole, participate to the roots, then aligning the fuselage gap screw 59; （ 2） the red nail into the upper rod 16 hole, participate to the roots, tighten fastening screws （ 3） the die mount in the die plate 19 holes in the die face, attention must be below the table plane 0~0.05mm, fastening on both sides of the locking screw 42. （4 ） will die platen mounted on the fuselage, set into the undershoot, turning a large belt pulley 32, the punch into the die hole, should uniform clearance, the upper and lower flexible, without interference and hard friction phenomenon, and then fastening mould plate and the fuselage of the fixing bolt （ 5） mounted on the feeder are removed parts. In 4, filling depth adjustment Unscrew the filling adjusting nut on both sides of the locking screw, nut is placed down can increase the depth of fill, after adjustment must tighten fastening screws, note the filling depth shall not exceed 45mm. In 5, the tablet thickness adjustment And on the connecting rod of the eccentric shell 05 on the eccentric sleeve 35, a ruler is arranged, the numerical representation on in depth into the mold. Adjusting the first unscrew eccentric casing 05 upper fastening bolt, through conical gear drives the eccentric sleeve to adjust the thickness of 35, after adjustment to the fastening bolt and nut, to prevent loosening. 6, the adjustment Rotation belt wheel （ clockwise ）, so that the lower rises to the highest position, loosen a screw adjusting nut on both sides, by rotating the adjusting nut so that the sheet, lower upper end face and the middle die plain-end, after adjustment, fastening screws on both sides. In 7, a feeder adjustment Rotation belt wheel to undershoot on end rises to the highest （ and D flat ）, regulation of flexible joint （ before adjusting nut ）, the front end of lower edges of the outer diameter near the feed nut, turn the pulley （ must be clockwise ） makes the feeder retreat movement several times still conforming to the requirements. 8, lower lever position adjustment directly influences the quantity of stability. Rotation belt wheel to undershoot decline lowest position, is filling the regulating nut tightly against the body, adjusting nut, so that the lower lever of semicircle head close to filling the regulating nut end face, and on a tight nut. Four, use and operation In 1, the machine must be inspected before use if there is a lack of side die, crack, deformation and other quality problems, check the machine the apparatus are in good condition. 2, check whether it meets the requirements of raw grain particles, particles of the fine powder content should not exceed 10%, so as not to affect the performance and service life of the machine. In 3, before the application of manual rotation of drive pulley or shun inching button pressure test, determine tablet conforms to the requirement, the machine is operating normally, can boot into production. In 4, the machine is equipped with a reverse inching button, pressing to produce laminated or upper punch sticking closed vehicle and check on progressive die in use, when in use, only allow instantaneous point makes the machine trace inversion, or mechanical damage. 5, use to keep the machine running conditions, such as abnormal sound, that should be down to check, troubleshooting and then use. Five, the maintenance and protection of In 1, parts is provided with a cup, can press cup type, respectively, to the lubricating oil or grease. Before starting the all refueling once, in the production of visual bearing temperature rise and operation of add. 2, check whether the operation is flexible and mechanical wear, defects found, timely repair. 3, once after use or production, should be brushing machine for each part of the residual powder; such as stops for a long time, shall die remove, and machine parts all wipe clean, smooth coated with antirust oil. 4, die maintenance: scrub clean, dry coated with antirust oil, is placed in a suitable container, keep clean, prevent the impact and damage. In six, matters needing attention In 1, when the power should pay attention to the operation of the machine direction, do not reverse; table free of mechanical damage. In 2, the machine, the power should be cut off, to avoid injury accidents. In 3, inverted point operation button only in relief or debugging observation on progressive die when using context, can not arbitrarily use, in order to avoid mechanical damage caused by the accident. 4, machine protective cover, safety cover before use should be arranged properly, can not be removed. 5, die should have no crack, deformation, short edge and other quality problems, substandard products do not use, so as to avoid the machine damage and effect on tablet quality. 6, regulation of parts or troubleshooting, must stop, so as not to cause personal injury. In 7, the gas, do not allow the oil spill from the outside, so as to avoid material pollution effects on tablet quality. | 
