简单介绍:
使用和注意:
1、本型烘箱应在室内工作,并安装平稳。
2、电源输入应装置的前级通断开关,并接妥良好地线。
3、必须检查电源、电压、电源接线无误后,方可通电使用。
4、在新购使用或搁置较久再用时,应先用低温烘烤80-100℃二小时后再开始升高温度,以利潮气外泄,增强绝缘性能和延长瓷件寿命。
5、仪表控温的热敏元件探头应从左侧线路的测温孔中插入工作室内,不得从箱顶气阀中心孔插入,以免影响使用。
6、本干燥箱初次使用时,应请勤加以观察,避免过热烘坏工件,造成损失。
7、使用如感到热惯稍大时,可关闭一组加热器以降低发热功率,防止惯性过大造成超温。
8、取入烘烤物件:请勿撞击伸入工作室的控温器部份,防止损坏控温器导致失灵。
9、本箱切忌烘烤易爆,易燃及挥发性的物品,以防爆炸。
10、如遇故障,请专业电工检修。
11、出厂时,工作室的搁板二块,说明书及合格证各一份。
技术参数:
型号101A | 电压(V) | 功率KW | 工作温度 范围(℃) | 控温 灵敏度℃ | 电机功率W | 工作室尺寸 MM | 外形尺寸 MM | 深×宽×高 | 深×宽×高 | —0 | 220 | 1.4 | 20-200 | ±5 | 40 | 250×300×300 | 350×660×663 | —1 | 220 | 3 | 20-300 | ±5 | 40 | 350×450×450 | 500×810×813 | —2 | 220 | 3.6 | 20-300 | ±5 | 40 | 450×550×550 | 600×910×913 | —3 | 220 | 4.6 | 20-300 | ±5 | 40 | 500×600×750 | 650×960×1113 | —4 | 3×380 | 9 | 20-300 | ±5 | 180 | 800×800×1000 | 1000×1170×1580 | —5 | 3×380 | 12 | 20-300 | ±5 | 370 | 1000×1000×1000 | 1200×1370×1580 | —6 | 3×380 | 15 | 20-300 | ±5 | 750 | 1000×1200×1200 | 1200×1570×1780 | —7 | 3×380 | 18 | 20-300 | ±5 | 750 | 1000×1200×1500 | 1200×1600×2100 | —8 | 3×380 | 21 | 20-300 | ±5 | 750 | 1200×1500×1500 | 1400×1900×2100 | | |
Simple introduction:
Use and pay attention:
In 1, the oven should work inside, and the installation of stationary.
In 2, a power input device for front on-off switch, and connected well good ground wire.
3, must check the power, voltage, power supply wiring correct, Party Ketong electricity use.
In 4, the new purchase or use a long use, should first be baked at a low temperature of 80-100 ℃for two hours after the start of elevated temperature, in order to tidal leakage, enhanced insulation properties and extend the life of porcelain pieces.
5 thermistors, temperature control instrumentation probe from the left line temperature measuring hole is inserted in the studio, not from the tank top valve is inserted into the central hole, so as not to affect the use.
In 6, the drying box when first used, should be invited to observe the ground, to avoid overheating drying bad work, resulting in the loss of.
7, the use of such as are thermal inertial slightly larger, can be closed by a group of heaters in order to reduce the heating power, prevent inertia caused by excessive temperature.
In 8, a baking object : do not crash into the studio thermostat parts, prevent damage leading to failure of temperature control device.
In 9, the box by baking and explosive, flammable and volatile items, to prevent an explosion.
10, in case of failure, please professional electrician maintenance.
11, the factory, the studio shelf two, specification and qualification certificate copies.
Technical parameters:
Model 101A voltage ( V ) power KW working temperature
( c ) range of temperature control
Sensitivity C motor power W studio size
MM dimensions
MM
Deep x width x height depth width x height
- 2201.4 20-200± 540250 x 300 x 300350 x 660 x 663
- 12203 20-300± 540350 x 450 x 450500 x 810 x 813
- 22203.6 20-300± 540450 x 550 x 550600 x 910 x 913
- 32204.6 20-300± 540500 x 600 x 750650 x 960 x 1113
- 43 ×3809 20-300± 5180800 x 800 x 10001000 x 1170 x 1580
- 53 ×38012 20-300± 53701000 x 1000 x 10001200 x 1370 x 1580
- 63 ×38015 20-300± 57501000 x 1200 x 12001200 x 1570 x 1780
- 73 ×38018 20-300± 57501000 x 1200 x 15001200 x 1600 x 2100
- 83 ×38021 20-300± 57501200 x 1500 x 15001400 x 1900 x 2100