进口衬氟闸阀
德国巴赫进口衬氟闸阀概述:
进口衬氟闸阀是一种zui带见的启闭阀门,利用两侧面密封呈楔状的闸板来接通或截断管路中介质,楔式闸阀不允许微量开启在管路中作节流装置用,以免因高速流动的介质冲蚀而加快密封面的损坏。FEP(F46)、PCTFE(F3)衬氟阀门适用在-50℃~150℃的各种浓度的王水、氢氟酸和各种有机酸、强酸、强氧化剂,FEP还适用于各种浓度的强碱有机溶剂以及其它腐蚀性气体、液体介质的管路上使用。
Imported fluorine gate valve
Introduction of the German Bach fluorine gate valve:
The import of fluorine valve is one of the most common with open and close the valve by two side sealing a wedge shaped medium to connect or disconnect the line, wedge gate valve does not allow for trace open throttle device in the pipeline, so as not to damage the sealing surface and accelerate the erosion caused by the medium high speed flow. FEP (F46), PCTFE (F3) fluorine valve for the aqua regia, hydrofluoric acid and various organic acids, strong acid, strong oxidizing agents in various concentrations of -50 DEG ~150 DEG C, the use of strong organic solvent FEP is also applicable to various concentration and other pipeline corrosive gas and liquid medium.
进口衬氟闸阀的定义:
1.阀体有扁体和圆体两种,阀体、阀盖、闸板的阀杆等直接与介质接触部件,全部包衬FEP(F46)或PCTFE(F3)等氟塑料。
2.密封副为FPE(F46)/FEP(F46)摩擦系数小,启闭力矩低。
3.填料采用PTFE(F4)标准填料,密封性能好,维修更换方便。
4.采用弹性闸板,可补偿闸板密封面与阀座密封面之间楔角偏差,吻合度好,密封效果理想。
5.介质可从两侧任意方向通过闸阀,适用于介质方向可能改变的管路上作启闭装置。
Imports of fluorine gate valve definition:
The 1 valve body and a flat cylinder two, valve body, valve cover, valve gate directly contacts with the media, all of the lining of FEP (F46) or PCTFE (F3) and fluorine plastic.
2 seal for FPE (F46) /FEP (F46) friction coefficient is small, the opening and closing torque is low.
3 packing with PTFE (F4) standard packing, good sealing performance, easy maintenance and replacement.
4 the use of elastic gate, can compensate the gate sealing surface and the valve seat sealing surface between the wedge angle deviation, good agreement, sealing effect is ideal.
5 medium can be used from both sides of any direction through the gate valve, suitable for the direction of the media may be changed on the pipeline for the opening and closing device.
进口衬氟闸阀技术参数:
产品名称 | 驱动方式 | 连接形式 | 结构形式 | 密封结构 | 压力范围 | 公称通径 | 常用材质 | 产品型号 |
进口衬氟闸阀 |
手动、电动、气动 |
法兰 |
明杆、暗杆 |
PTFE、PCTFE、FEP |
1.0-2.5MPa |
DN15-500 |
铸钢、不锈钢 |
bach-a |
阀门尺寸标准
| 阀门试验标准
| 阀门交货标准
| 工业阀门标准
| 法兰阀门标准
| 焊接阀门标准
| 对夹式连接阀
| 内螺纹连接阀
| 可以提供美国 |
DIN EN558-2005
| DIN EN12266-1-2003
| DIN3230-2-1974
| DIN EN 1171-2003
| DIN EN 3202-1977
| DIN EN 3202-1982
| DIN EN 3202-1979
| DIN EN 3202-1977
| API、ANSI等标准
|
进口衬氟闸阀guan网:http://www.twvalve。。net/html/3507.html