制药网
详细介绍
导热系数测定仪是检测仪器，用于测量各种匀质板材状绝热保温材料的导热系数及复合板材的测定。使用前务必仔细阅读说明书。并由实验人员操作，以避免操作不当引起的伤害。如需了解更多资料请与我公司客服人员联系。
Thermal conductivity tester is a testing instrument for measuring the thermal conductivity of various homogeneous plate-like thermal insulation materials and the determination of composite plates. Be sure to read the instructions carefully before use. It is operated by experimental personnel to avoid injury caused by improper operation. For more information, please contact our customer service staff.
导热系数测定仪按照GB/10294-2008《绝热材料稳态热阻及有关特性的测定，热流计法》设计制造。适用于检测单位、大专院校、科研生产单位使用。采用大屏幕触摸屏具有操作简便，智能化程度高等优点。
The thermal conductivity tester is designed and manufactured in accordance with GB / 10294-2008 "Determination of steady-state thermal resistance and related characteristics of thermal insulation materials, heat flow meter method". Applicable to testing units, colleges and universities, research and production units. The large-screen touch screen has the advantages of easy operation and high intelligence.
导热系数测定仪主要特点：
★微机自动控制，自动完成数据采集和生成报表，智能化程度高，使检测快捷、准确。
★主机箱采用复合没计，使用方便，外观新颖大方。
★冷单元部分采用自动汽缸夹紧，气动系统压力值可调。
★冷系统采用全封闭式压缩机组，冷却快、制冷均匀、运行噪音小。
★计量加热单元采用紫铜板作为加热面板。具有高导热性，使温度均匀热惯性小，测量结果更准确。
Main characteristics of thermal conductivity tester:
★ Microcomputer automatic control, complete data collection and report generation automatically, high degree of intelligence, make detection fast and accurate.
★ The main box adopts composite design, convenient to use and novel in appearance.
★ The cold unit is clamped by an automatic cylinder, and the pressure value of the pneumatic system is adjustable.
★ The cooling system uses a fully enclosed compressor unit, which has fast cooling, uniform cooling and low operating noise.
★ The metering heating unit uses a copper plate as the heating panel. With high thermal conductivity, uniform temperature and low thermal inertia, more accurate measurement results.
导热系数测定仪技术参数：
★热板温度范围：常温—80℃
★冷板温度范围：10～50℃
★试件规格尺寸：300X 300mm
★试件厚度范围：10～40mm
★测试准确度：≤±3％
★电源、功率：220V／2KW
★外形尺寸：800×600×1600mm
Technical parameters of thermal conductivity tester:
★ Temperature range of hot plate: normal temperature—80 ℃
★ Cold plate temperature range: 10 ～ 50 ℃
★ Specifications of test piece: 300X 300mm
★ Test piece thickness range: 10 ～ 40mm
★ Test accuracy: ≤ ± 3%
★ Power supply and power: 220V / 2KW
★ Dimensions: 800 × 600 × 1600mm
导热系数测定仪工作原理：
型导热系数测定仪，采用双试件测定装置，防护热板组：包括加热单元、冷却单元。 加热单元应分为在中的计量单元和由隔缝分开的环绕计量单元的防护单元，并装有绝热装置。 热单元采用双热面加热器，冷板与双热面对称布置，根椐试件的厚度设定移动冷板的空间，将被测试件垂直放置在两个相互平行具有恒定温度的平板中，在稳定状态下，试件中测量部分具恒定热流，通过测定稳定状态下流过计量单元的一维恒定热流量Q、计量单元的面积A、试件冷、热表面的温度差T,可计算出试件的热阻R，根据试件的厚度， 可以准确算出试件的导热系数入值。
Thermal conductivity tester works:
Type thermal conductivity tester, using double test piece measuring device, protective hot plate group: including heating unit, cooling unit. The heating unit shall be divided into a metering unit in between and a protective unit surrounding the metering unit separated by a gap, and equipped with thermal insulation. The hot unit adopts double hot surface heaters. The cold plates are arranged symmetrically with the double hot surfaces. The thickness of the test piece sets the space for moving the cold plate. The test piece is placed vertically in two flat plates with constant temperature parallel to each other. In the steady state, the measurement part of the test piece has a constant heat flow. By measuring the one-dimensional constant heat flow Q flowing through the metering unit, the area A of the metering unit, and the temperature difference T between the cold and hot surfaces of the test piece, it can be calculated. According to the thickness of the test piece, the thermal resistance R of the test piece can be accurately calculated.
导热系数测定仪注意事项：
接地保护线必须可靠接地，开机前检查电源电压是否正常。
制冷系统严禁连续启动，启动间隔应大于3分钟。
试件的测试温度一定要低于试件的熔点温度。
温度过高，电源被切断，查找原因后方可重新检测。
试验结束, 点 “自动检测"键复位后再点“退出"键。
自动运行中不要点“退出" 和“手动调控"，否则实验终止或出现失控。
制冷系统制冷剂为R十二。
系统通电时不许触摸可能带电部位。
本装置在运输搬运和移动位置时，禁止用杆子撬动底部，避免损坏 制冷系统。运输搬运时利用顶部吊环移动或搬运。搬运时整机的倾斜角度不应超过45°角，防止损坏制冷压缩机。
Note for thermal conductivity tester:
The grounding protection wire must be reliably grounded. Check whether the power supply voltage is normal before starting up.
Refrigeration system is strictly forbidden to start continuously. The start interval should be more than 3 minutes.
The test temperature of the test piece must be lower than the melting point of the test piece.
The temperature is too high, the power is cut off, and the cause can be checked again.
After the test, click the "Auto Detect" button to reset and then click the "Exit" button.
Do not click "Exit" and "Manual Control" during automatic operation, otherwise the experiment will be terminated or out of control.
Refrigeration system refrigerant isR十二.
Do not touch any live parts while the system is powered on.
When the device is transported and moved, it is forbidden to pry the bottom with a pole to avoid damaging the refrigeration system. Use the top ring to move or carry during transportation. The tilt angle of the whole machine should not exceed 45 ° during transportation to prevent damage to the refrigeration compressor.
制药网