详细介绍
型号概述
TBS1064 | TBS1104 | TBS1154 | |
---|---|---|---|
带宽 1 | 60 MHz | 100 MHz | 150 MHz |
通道 | 4 | 4 | 4 |
每条通道的取样速率 | 1.0 GS/s | 1.0 GS/s | 1.0 GS/s |
记录长度 | 在所有时基上 2.5k 点 |
1在2 mV/div 时带宽是 20 MHz
垂直系统 — 模拟通道
垂直分辨率
8 位
输入灵敏度范围
使用经校准的微调时所有型号均为 2 mV 至 5 V/div
DC增益精度
±3%,从 10 mV/div 至 5 V/div
输入电压
300 VRMS CAT II;超过 100 kHz 时以 20 dB/倍频程下降至 3 MHz 时的 13Vp-p AC
偏置范围
2 mV 至 200 mV/div:±1.8 V
>200 mV 至 5 V/div:±45 V
带宽限制
20 MHz
输入耦合
AC、DC、GND
输入阻抗
1 MΩ,并联 20 pF
垂直缩放
垂直扩展或压缩动态或停止波形
水平系统 — 模拟通道
时基范围
5 ns 至 50 s/div
时基精度
50 ppm
水平缩放
水平扩展或压缩动态或停止波形
输入/输出端口
USB 接口
前面板上的 USB 主控端口支持 U 盘
仪器背面的 USB 设备端口支持连接到 PC 和所有 PictBridge® 兼容打印机
GPIB 接口
选配
数据存储
非易失存储器
参考波形显示
2.5K 点参考波形
没有 U 盘时的波形存储
2.5K 点
U 盘容量
64 GB
有 U 盘时的波形存储
每 8 MB 96 个或以上参考波形
没有 U 盘时的设置
10 个前面板设置
有 U 盘时的设置
每 8 MB 有 4000 个或更多前面板设置
有 U 盘时的屏幕图
每 8 MB 128 个或以上屏幕图(图像数量取决于选择的文件格式)
有 U 盘时全部保存操作
每 8 MB 12 个或以上全部保存操作
一次全部保存操作会创建3~9个文件(设置、图像、外加显示的每个波形一个文件)
采集系统
采集模式
峰值检测
高频随机毛刺捕获。5 μs/div 至 50 s/div 的所有时基设置均可捕获窄至 12 ns(典型值)的毛刺。
采样
仅采样数据
平均值
平均波形,选配范围: 4、16、64、128
单序列
使用“单序列"按钮,捕获一个已触发的采集序列
滚动
采集时基设置为 >100 ms/div
触发系统
外部触发输入
所有型号均包括
触发模式
自动、正常、单序列
触发类型
边沿(上升沿/下降沿)
常规的电平驱动触发。任一通道均提供正斜率或负斜率。耦合选项:交流、直流、噪音抑制、高频抑制、低频抑制
视频
所有行或单个行、复合视频的奇数场/偶数场或所有场或者广播制式(NTSC、PAL、SECAM)均可触发。
脉冲宽度(或毛刺)
脉冲宽度小于、大于、等于或不等于均可触发,选配时限范围为 33 ns 至 10 s
触发源
四通道型号:CH1、CH2、CH3、CH4、Ext、Ext/5、交流线路
触发视图
按下“触发视图"按钮时显示触发信号。
触发信号频率读数
提供触发源的频率读数。
波形测量
光标
触发类型
幅度、时间
测量
ΔT、1/ΔT、ΔV
自动测量
周期、频率、+ 宽度、- 宽度、上升时间、下降时间、值、最小值、峰-峰值、平均值、RMS、周期 RMS、光标 RMS、占空比、相位和延迟
波形数学运算
算数
加、减、乘
数学函数
FFT
FFT
Windows:Hanning、平顶、矩形
2048 个采样点
信号源
CH1 – CH2、CH2 – CH1、CH1 + CH2、CH1 × CH2、CH3 – CH4、CH4 – CH3、CH3 + CH4、CH3 × CH4
自动设置
自动设置菜单
单一按钮,自动设置垂直、水平和触发器系统的所有通道,可撤销自动设置
方波
单循环、多循环、上升与下降缘
正弦波
单循环、多循环、FFT 波谱
视频(NTSC、PAL、SECAM)
现场: 所有、奇数或偶数
行: 所有行号或可选择行号
自动量程
在点间移动探头或者信号呈现较大变化时,自动调节垂直和/或水平示波器设置。
主要性能指标
150 MHz、100 MHz 和 60 MHz 带宽型号
4 通道型号
全部通道均实现 1 GS/s 采样率
所有通道上 2.5k 点记录长度
高级触发,包括脉宽触发和选行视频触发
主要功能
16 个自动测量和 FFT 分析可简化波形分析
内置的波形极限测试
自动化、扩展的数据记录功能
自动设置和信号自动量程
内置的上下文相关帮助
探头自检
多语言用户界面
5.7 英寸(144 毫米)有源 TFT 彩色显示器
体型小,重量轻 - 仅 4.9 英寸(124 毫米)厚,重 4.4 磅(2 公斤)
连接
前面板配有 USB 2.0 主控端口,存储数据便捷
后面板上有 USB 2.0 设备端口用于连接 PC 或直接打印到 PictBridge® 兼容打印机
包括用于连接平台的 Tektronix OpenChoice® 软件
数字精度,精确测量
带宽高达 150 MHz,采样率达 1 GS/s,远高于同等价位的其他数字存储示波器。泰克专有采样技术能够实时采样,所有通道均实现指明的采样率,始终准确捕获信号。使用多条通道时不会降低采样性能。
TBS1000 数字示波器系列特别适合满足当前苛刻的测量要求需求。TBS1000 系列拥有多种功能和内置工具,易学易用,特别适合初次使用示波器的用户或使用经验丰富的人员。TBS1000 系列拥有与 Tektronix TDS 示波器家族相同的用户界面,操作 TBS1000 时您是在使用流行的示波器平台。运行的泰克示波器数量已经超过 500,000 台。
为简化与现有课程的整合,TBS1000 还包括一张教育资源光盘,其中装有多种工具,可帮助新手掌握示波器的使用方法。TBS1000 以您可以承受的价格,提供您需要的工具和性能。
检修设备的工具
包括上升沿/下降沿、脉冲宽度和视频在内的高级触发功能,帮助您快速隔离所需信号。只要捕获到信号,高级数学运算功能和自动化测量功能便可加快分析速度。执行 FFT 或加、减或乘波形十分迅速。16 种自动化测量功能,快速可靠地计算频率或上升时间等重要信号特点,内置极限测试功能轻松识别信号中的问题。
专为方便您的工作而设计
TBS1000 系列示波器采用易用且熟悉的操作设计,满足您对泰克的一贯期望。
直观操作
直观的用户界面配有每条通道专用垂直控制、自动设置和自动量程的功能,使这些仪器变得简单易用,从而缩短学习时间,提高工作效率。
随时随地助您一臂之力
内置的帮助菜单提供有关示波器特点和功能的重要信息。使用与用户界面相同的语言提供帮助。
探头自检
进行测量前,只要使用一个按钮便可启动快速、简便的程序,检查探头补偿状况。
极限测试
示波器可以判断输入波形是否超过预定义边界,自动监测源信号和输出的通过或失败结果。违规时可以触发特定动作,包括停止波形采集、停止极限测试功能、将失败的波形数据或屏幕图像保存到 USB 存储设备中或者上述动作的任何组合操作。这为制造或服务应用提供了理想的解决方案,因为这些应用需要快速做出决策。
灵活地传送数据
使用前面板上的 USB 主控端口,快速保存仪器设置、屏幕截图和波形数据。内置的数据记录功能可以设置示波器,将用户的触发波形保存到 USB 存储设备中,时间长达 24 小时。还可以选择“无限"选项不间断监控波形。该模式可以将触发波形保存到外部 USB 存储设备,没有时间长度限制,直到存储设备存满为止。示波器还会到时引导您插入另一个 USB 存储设备以继续保存波形。
PC 连接方便
使用后面板 USB 设备端口和随附的 OpenChoice PC 通信软件捕获、保存和分析测量结果,非常方便。将屏幕图像和波形数据拖入独立桌面应用程序或直接拖入 Microsoft Word 和 Excel,十分简单。或者,如果您不愿意使用 PC,也可以直接连接任何兼容 PictBridge 打印机来打印图像。
Vertical system - analog channel
Vertical resolution
eight
Input sensitivity range
All models are 2 mV to 5 V/div with calibrated fine tuning
DC gain accuracy
Plus or minus 3%, from 10 mV/div to 5 V/div
Maximum input voltage
300 VRMS CAT II; 13vp-p AC with a frequency range of 20 dB/ x over 100 kHz down to 3 MHz
Offset range
2 mV to 200 mV/div: plus or minus 1.8v
>200 mV to 5 V/div: plus or minus 45 V
Bandwidth limitations
20 MHz
The input coupling
AC, DC, GND
The input impedance
1 M Ω, 20 pF in parallel
Vertical scaling
Expand or compress the dynamic or stop waveform vertically
Horizontal system - analog channel
Time base scope
5 ns to 50 s/div
Accuracy of time base
50 PPM
The level of zoom
Horizontal expansion or compression of dynamic or stop waveforms
Input/output ports
The USB interface
The USB master port on the front panel supports the USB disk
Instruments on the back of the USB device port support connected to the PC and all PictBridge ® compatible printer
GPIB interface
optional
Data is stored
Non-volatile memory
Reference waveform display
2.5k reference waveform
Waveform storage without a usb drive
2.5 K
Maximum usb capacity
64 GB
Waveform storage with usb drive
96 or more reference waveforms per 8 MB
No Settings for usb drives
10 front panel Settings
The Settings when you have a usb drive
There are 4,000 or more front panel Settings per 8 MB
A screen image of a usb drive
128 screens per 8 MB or more (the number of images depends on the file format you choose)
Save everything when you have a usb drive
Every 8 MB 12 or more save operations
A full save operation creates 3 to 9 files (setup, image, plus one file for each waveform displayed)
Acquisition system
Acquisition mode
Peak detection
High frequency random burr capture. 5. All the time base Settings in the range of 5 lefs /div to 50 s/div can capture the burrs as narrow as 12 ns (typical value).
The sampling
Sampled data only
The average
Average waveform, optional range: 4, 16, 64, 128
Single sequence
Use the single sequence button to capture a triggered collection sequence
rolling
The base is set to >100 ms/div at collection time
The trigger system
External trigger input
All models are included
Trigger mode
Automatic, normal, single sequence
Trigger type
Edge (up/down edge)
Normal level drive trigger. Either channel provides a positive slope or a negative slope. Coupling options: ac, dc, noise suppression, high frequency suppression, low frequency suppression
video
All rows or single rows, odd field/even field of compound video or all fields or broadcast modes (NTSC, PAL, SECAM) can be triggered.
Pulse width (or burr)
The pulse width can be triggered if it is less than, greater than, equal to or not equal to 33 ns to 10 s
Trigger source
Four channel models: CH1, CH2, CH3, CH4, Ext, Ext/5, communication lines
The trigger view
The trigger signal is displayed when the trigger view button is pressed.
Trigger signal frequency reading
Provides a frequency reading of the trigger source.
Waveform measurement
The cursor
Trigger type
Amplitude time
measurement
Δ T, 1 / Δ T, Δ V
Automatic measurement
Period, frequency, + width, -width, -width, rise time, fall time, maximum, minimum value, peak value, average value, RMS, period RMS, cursor RMS, duty ratio, phase and delay
Waveform mathematics
count
Plus, minus, times
Mathematical function
FFT
FFT
Windows: Hanning, flat top, rectangle
2048 sampling points
Signal source
CH1 -- CH2, CH2 -- CH1, CH1 + CH2, CH1 x CH2, CH3 -- CH4, CH4 -- CH3, CH3 + CH4, CH3 x CH4
Automatically set
Automatic setting menu
Single button that automatically sets all channels of the vertical, horizontal and trigger systems
Square wave
Single cycle, multiple cycle, rising and falling edge
Sine wave
Single cycle, multiple cycles, FFT spectrum
Video (NTSC, PAL, SECAM)
Field: all, odd or even
Line: all line Numbers or optional line Numbers
Automatic range
The vertical and/or horizontal oscilloscope Settings are automatically adjusted when the probe or signal changes significantly from point to point.
Display system
The interpolation
Sin (x)/x
The wave type
Point, vector
afterglow
Close, 1 second, 2 seconds, 5 seconds, unlimited
format
YT and XY
The physical characteristics of
Appearance of size
highly
158.0 mm (6.22 in.)
The width of the
326.3 mm (12.85 inches)
The thickness of the
124.2 mm (4.89 in.)
The loading size
highly
266.7 mm (10.5 inches)
The width of the
476.2 mm (18.75 inches)
The thickness of the
228.6 mm (9.0 in.)
The weight of the
Only the instrument
2.0kg (4.4lb)
... Including attachments
2.2 kg (4.9 LBS)
RM2000B rack mounting
The width of the
482.6 mm (19.0 in.)
highly
177.8 mm (7.0 in.)
The thickness of the
108.0 mm (4.25 in.)
Environmental characteristics
The temperature
work
0 to 50 DHS C +
non-working
- 40 to 71 DHS C +
humidity
Working humidity and non-working humidity
Plus 40 is up to 85% RH when C or below
As high as +50, it's 45 percent RH
The altitude
Working humidity and non-working humidity
Maximum 3000 m (9,843 ft)
Laws and regulations
Electromagnetic compatibility
Class A of instruction 2004/108/EC, EN 61326-2-1; Australian EMC Framework (EMC Framework) regulations
security
Ul61010-1:2004, CSA22.2 no. 61010-1:2004, en61010-1:2001, iec61010-1:2001
TBS1000 digital storage oscilloscope series design compact, high cost performance. TBS1000 series oscilloscope integrates various standard functions, including USB connection, 16 kinds of automatic measurement, limit test, data record and context-related help.
Main performance index
150 MHz, 100 MHz and 60 MHz bandwidth models
4 channel model
All channels achieve 1 GS/s sampling rate
Record length at 2.5k points on all channels
Advanced trigger, including pulse width trigger and select row video trigger
The main function
16 automatic measurements and FFT analysis can simplify waveform analysis
Built-in waveform limit test
Automatic and extended data recording function
Automatic setting and signal automatic range
Built-in contextual help
The probe self-inspection
Multilingual user interface
5.7-inch (144 mm) active TFT color display
Small in size and light in weight - 4.9 inches (124 mm) thick and 4.4 pounds (2 kg)
The connection
The front panel is equipped with USB 2.0 main control port, which is convenient to store data
On the rear panel has a USB 2.0 device ports used to connect to a PC or print directly to the PictBridge ® compatible printer
Including used to connect platform Tektronix OpenChoice ® software
Digital accuracy, accurate measurement
Bandwidth up to 150 MHz, maximum sampling rate up to 1 GS/s, far higher than other digital storage oscilloscopes at the same price. Teck's proprietary sampling technology enables real-time sampling, all channels achieve the specified sampling rate, and always accurately capture signals. Sampling performance is not reduced when multiple channels are used.