官方微信|手机版|本站服务|买家中心|行业动态|帮助

产品|公司|采购|招标

进口化工流程泵美国化工流程泵

参考价面议
具体成交价以合同协议为准
  • 公司名称上海凡而阀门有限公司
  • 品       牌
  • 型       号TYLER
  • 所  在  地上海
  • 厂商性质代理商
  • 更新时间2017/5/8 18:51:19
  • 访问次数474
在线询价 收藏产品 查看电话 同类产品

联系我们时请说明是 制药网 上看到的信息,谢谢!

上海凡而阀有限公司是一家具有二十多年历史的大型阀门生产企业,是全国Z主要和较大的闸阀、截止阀、球阀、蝶阀、水力控制阀等通用阀门供应商之一。在石油、化工、冶金、电力、建筑、热力、供水等行业具有很高的度及影响力。产品一直供不应求,国内外市场。 

 

上海凡而阀有限公司秉着“以诚为本,互惠双赢的原则,服务于广大客户。全面实行标准化、专业化、科学的管理制度,公司始终坚持诚品求生存,科技求发展的经营方针,在产品品质上以精益求精,追求*为质量方针。

球阀、针型阀、截止阀、闸阀、止回阀、蝶阀、阻火器、排气阀、排泥阀、过滤器、放料阀、隔膜阀、安全阀、旋塞阀、手机:13917909444
进口化工流程泵美国化工流程泵

进口化工流程泵优点:
叶轮可用闭式、半开式、开式三种。可输送清洁,含颗粒,含少量气体介质。也可输送高温、低温、强腐蚀介质。叶轮设有平衡孔加耐腐环,平衡轴向力。  2 泵体和轴承架用中间连接段连接。根据不同的工况条件,中间连接段可采用不同的材质,避免输送强腐蚀介质时轴承架、轴承严重腐蚀。同时中间连接段设有水冷腔,通冷却循环水,阻隔高温介质将高温传到轴承上。  3
进口化工流程泵美国化工流程泵 产品信息

  进口化工流程泵美国化工流程泵

 

进口化工流程泵优点:

叶轮可用闭式、半开式、开式三种。可输送清洁,含颗粒,含少量气体介质。也可输送高温、低温、强腐蚀介质。叶轮设有平衡孔加耐腐环,平衡轴向力。  2 泵体和轴承架用中间连接段连接。根据不同的工况条件,中间连接段可采用不同的材质,避免输送强腐蚀介质时轴承架、轴承严重腐蚀。同时中间连接段设有水冷腔,通冷却循环水,阻隔高温介质将高温传到轴承上。  3 密封形式可采用填料密封,单、双端面机械密封,集装式单端面机械密封。根据不同情况和用户对冷却与冲洗要求。 4 轴承架设计有空冷散热片、风冷风扇、水冷腔三种形式,用户可根据使用工况选用。轴承由油环从油箱里溅稀油润滑。油箱内的油由水冷腔的水冷却,轴承内的热由冷水带走,以保证轴承随时处于正常工作状态。  5 根据介质温度和压力等情况,支撑形式采用中心支撑和脚架支撑。 

 

进口化工流程泵工作原理:

化工泵在工作前,泵体和进料管必须罐满液体行成真空状态,当叶轮快速转动时,叶片促使液体很快旋转,旋转着的液体物料在离心力的作用下从叶轮中飞去,泵内的水被抛出后,叶轮的中心部分形成真空区域。液体物料在大气压力的作用下通过管网压到了进料管内。这样循环不已,就可以实现连续输送。

在化工泵启动前,泵壳内灌满被输送的液体;启动后,启动后,叶轮由轴带动高速转动,叶片间的液体也必须随着转动。在离心力的作用下,液体从叶轮中心被抛向外缘并获得能量,以高速离开叶轮外缘进入蜗形泵壳。

在蜗壳中,液体由于流道的逐渐扩大而减速,又将部分动能转变为静压能,zui后以较高的压力流入排出管道,送至需要场所。液体由叶轮中心流向外缘时,在叶轮中心形成了一定的真空,由于贮槽液面上方的压力大于泵入口处的压力,液体便被连续压入叶轮中。可见,只要叶轮不断地转动,液体便会不断地被吸入和排出。

进口化工流程泵技术参数:

流量:9.5~2000m3/h          
扬程:4~160m
转速:1450、2900r/min     
功率:1.1~160KW
口径:32~300mm       
工作压力:2.5MPa
工作温度:-40~+300
特性曲线平坦,气蚀值低,在不满负荷时,也保持这些特性。

 

美国泰乐TYLER售后服务:
*的服务铸就*的企业让客户无后顾之忧。
1、按合同要求提供产品的合格证、铭牌、检验报告、产地证名、安装说明书等。
2、顾客在验收产品过程中,如出现与合同要求不符时,我司接到顾客通知后两小时内给予处理。
3、我司提供十二个月以上产品质保期,时间从验收合格之日起计算。
4、在正确安装和使用下,出现产品质量问题,本公司将负责到底。

 

 

Chemical process pump

Advantages of imported chemical process pump:

Impeller can be closed, semi open, open three. Can be cleaned clean, containing particles, containing a small amount of gas medium. High temperature, low temperature, strong corrosive medium. The impeller has a balance hole Jianai rot ring, axial force balance. 2 pump body and bearing frame with intermediate connection. According to the different working conditions, the middle connecting section can adopt different materials, so as to avoid the serious corrosion of the bearing frame and the bearing. At the same time, the middle connecting section is provided with a water cooling cavity, which is used for cooling the circulating water and blocking the high temperature medium to transfer the high temperature to the bearing. The 3 seal form can be used for single and double packing seal, mechanical seal, container type single mechanical seal. According to different conditions and user requirements for cooling and flushing. 4 bearing frame is designed with air cooling radiator, air cooling fan, water cooling cavity in three forms, users can choose according to the working conditions. The bearings are lubricated by oil rings from the oil tank. The oil in the oil tank is cooled by the cooling water, and the heat inside the bearing is taken away by cold water to ensure that the bearing is in normal working condition at any time. 5 according to the medium temperature and pressure, the central support and support leg.  

Working principle of chemical process pump:

Chemical pump before work, the pump body and the feeding pipe must be tank full of liquid into the vacuum, when the impeller rotates fast, fast rotating blades to the liquid, liquid material whirling role under the centrifugal force and flew from the impeller, pump the water is thrown, the impeller formed the center of the Ministry of vacuum area. Under the action of atmospheric pressure, the liquid material is pressed into the feed pipe through the pipe network. This endless cycle, you can achieve continuous delivery.

Before the start of the chemical pump, the pump shell is filled with the liquid to be delivered; after the start, start, the impeller driven by the high-speed rotation of the shaft, the liquid between the blades must also be with the rotation. Under the action of centrifugal force, the liquid was thrown from the impeller center and outer edge of the energy leaving the impeller at high speed into the outer pump shell shaped cochlea.

In the spiral case, the liquid due to the gradual expansion of the flow path and slow down, and some of the kinetic energy into static pressure, and finally into the discharge pipeline with high pressure, sent to the required place. The liquid from the impeller center to the outer edge of the impeller center, the formation of a certain vacuum, due to the pressure tank above the liquid level is greater than the pressure pump at the entrance, the liquid will be pressed into the impeller in a row. Visible, as long as the impeller continues to rotate, the liquid will continue to be inhaled and discharged.

Technical parameters of imported chemical process pump:

Flow rate: 9.5 ~ 2000m3/h

Head: 4 ~ 160m

Speed: 1450, 2900r/min

Power: 1.1 ~ 160KW

Diameter: 32 ~ 300mm

Working pressure: 2.5MPa

Operating temperature: -40 ~ +300 C

The characteristic curve is flat and the cavitation value is low, and these characteristics are also maintained at the time of the load.

The United States TYLER Taylor customer service service:

The first-class service created a first-class enterprise so that customers no worries.

1, according to the contract requirements for product certification, nameplate, inspection report, certificate of origin, installation instructions etc..

2, the customer in the process of acceptance of the product, such as the emergence of the contract requirements and inconsistent, I received the notification of the customer within two hours after the treatment.

3, our company provides more than twelve months warranty period, the time from the date of acceptance.

4, in the correct installation and use, product quality problems, the company will be responsible in the end.

客户须知:

询问美国泰乐TYLER电磁阀一级代理商。销售一部(上海凡而阀门有限公司),参数提供如下:

1.公称通径2、公称压力3、流体性质(包括温度、介质) 4.材质 5.连接方式 6电源.电压7、控制方式(常开式、常闭式、自保持式).8、防护形式(防爆型、防水型、防尘型、防潮型、防腐型、普通型)

 

 

美国泰乐相关领域业绩:杭州地铁1号线、杭州地铁2号线、杭州地铁4号线,南京地铁1号线、南京地铁2号线、南京地铁3号线、南京地铁4号线、南京地铁10号线。

 

帝国化学工业、美国科氏工业、美国联合能源、艾默生电气、卢克石油、中国海洋石油

 

 

美国泰乐代理商上海凡而阀门有限公司,咨询:

 

Customer information:

Welcome to inquire us Taylor TYLER solenoid valve agents. Sales of a (Shanghai and valve Co., Ltd.), the parameters are provided as follows:

1 nominal diameter, nominal pressure 3, 2 fluid properties (including temperature, medium) 5 connection 4 material 6 power. 7, voltage control mode (normally open and normally closed, self retaining.8), protection (explosion-proof, waterproof, dustproof, moistureproof and anticorrosive type type type, ordinary type)

The United States Taylor related field performance: Hangzhou Metro Line 1, Hangzhou Metro Line 2, Hangzhou Metro Line 4, Nanjing Metro Line 1, Nanjing Metro Line 2, Nanjing Metro Line 3, Nanjing Metro Line 4, Nanjing Metro Line 10.

Imperial chemical industries, the United States of America, the United States, Emerson, Luke electric, China National Offshore oil.

The United States and Shanghai where agents Taylor Valve Co. Ltd., consulting:

 

 

 

 

进口化工流程泵guan网:http://www.twvalve。。net/html/2255.html

同类产品推荐
在找 进口化工流程泵美国化工流程泵 产品的人还在看

提示

×

*您想获取产品的资料:

以上可多选,勾选其他,可自行输入要求

个人信息: